Children’s Cotton Padded Clothes Cutting Drawing Size Drawing Of Baby Cotton Padded Clothes And Trousers

womens one piece swimsuits p3754 i1

Introductionintroduction

when the cold weather comes, many mothers begin to work on their children’s warm clothes, and cotton padded clothes and trousers are essential to keep out the cold. Although the cotton padded clothes and trousers bought are also very good, many skillful mothers will still make clothes for their children by themselves. Looking at their children wearing clothes made by their mothers with love, they feel warm even in cold weather. Next, Xiaobian will teach you how to make baby’s cotton padded clothes and trousers. Mothers, hurry up and learn

Children’s cotton padded clothes cutting figure

1. Prepare a newspaper, fold it in half and then fold it in half, as shown in the dotted line fold in the figure

2. The folded newspaper is shown in the figure. The rosy part is the folded place. Don’t be wrong, otherwise the next steps will be in vain

3. Measure the size of the baby, and you can draw the shape of the main film on the newspaper

4. Open it and see if you can see the shape? The position of the mark just left is the collar position of the cotton padded jacket. Now let’s make the front film, as shown in the figure

5. Let’s cut the back piece. The neckline of the back piece should be cut out with the same width as the front piece, as shown in the figure

6. Next, you can compare the newspaper to cut out the front and back pieces of the cotton padded jacket. After cutting, sew the front and back pieces according to the rose red stitch in the figure

7. Compare the newspaper with the lining, cut out the lining, and leave a hole for cotton when sewing, as shown in the figure

8. Put the inner piece in the outer piece and wrap the edge along the yellow line. Such a cotton padded jacket will be more beautiful

9. Cut out the collar piece according to the collar length of the front piece and the back piece. The round collar is used in this tutorial. Personally, I think this collar type will be very cute

10. Sew the collar piece along the rose red stitch, and add a small pocket, so it will be very convenient to put things

11. It will be lucky to stick a small square red cloth in the middle of the back of the cotton padded jacket

The last step: put the cotton evenly from the opening just left, and then sew the opening with a hand needle, and it’s finished

Precautions

1. Size

The down jacket will expand because it needs to be filled with down. In this way, the clothes will be shortened and shrunk. When we draw the picture, we need to increase the amount. The specific amount depends on the amount of down filling and the partition line pressed. The more down, the denser the line is pressed, the more shrinkage, and vice versa

Take this one as an example: the filling amount of clothes is about 80g, the bust of Baojing is 29*2, the bust of normal cotton padded jacket is 40*2, and this down jacket is 43*2, with close sleeves and shoulder width of about 2cm. The ideal length I want is 54 cm, and the volume is 5cm. The finished length is exactly 54cm; The ideal sleeve length is 42cm, measured 4cm, and the finished size is 43cm This is just a reference, and the details should be determined according to the style

2. Cropping

I cut the clothes’ surface cloth and gallbladder cloth by folding them together. The size is the same. The width and size of the lining cloth remain the same, and the length should be shortened, because the surface cloth will be shortened after filling. If the lining cloth is cut according to the normal size, the lining will be longer than the surface cloth after it is made, and it may leak out. In order to be beautiful, the length of the cloth is reduced by 2cm, and the sleeve length is reduced by 1cm

3. Fold the edge line

There is no fleece in the 3cm inside after the folding of the watch cloth, so before the frame line between the watch cloth and the gall cloth, press a line at the folding place of the two layers of gall cloth

4. Dark pocket

After the frame line between the table cloth and the gall cloth, draw the lint separation line on the table cloth. The line that passes through the dark pocket will be turned out first, and the rest of the lint separation line will not be turned. Then start to make the pocket. Put silk wool inside the cover on the pocket to make it full. If the open pocket can be made after filling and pressing the thread. (one front panel has two filling ports)

5. Plush filling

Put on a mask, wear clothes that imitate sticky fleece, and handle them with care when loading, (be sure to pay attention when loading fleece, and don’t put it between the watch cloth and the gall cloth until you see it clearly, remember!). Usually, the fleece in the sleeve is thinner than the body of the clothes. After filling one, clamp it with a clip, and clean the battlefield after filling it all (it’s best to do it in the bathroom, so it won’t fly all over the room, and it’s convenient to clean it). Finally, press and separate the lint (with synchronous presser foot). First, use your hand to beat the lint evenly, and then empty the air with your hand. First press the middle, and then press the lines on both sides

6. Lining stitching

In order to prevent the lining from being off stitched, it is best to lock the edge when sewing. After locking the edge, the seam will be overwhelmed, and the seam will be pressed from the front 0.1cm away from the seam

7. Length of welt outside the placket

As the clothes will be shortened after being made, if the placket is cut according to the size of the drawing, it will obviously grow in the front and middle. In order to look good, my method is that the placket is cut 2cm shorter than the size of the drawing, and the 2cm more than the body is shrunk to the inside during sewing. A layer of cotton is also placed inside the placket, so it won’t appear too thin

8. Zipper

The length of the zipper of the down jacket is 2cm shorter than the size of the drawing, which is the same as the length of the lining. When sewing, the extra 2cm on the surface cloth is shrunk to the inside, and it should not be concentrated in one place

9. Embossing line

When pressing lines, try to flatten the bottom cloth to prevent the bottom from overlapping and reduce rework

10. Fixed connection point

After the clothes are made, connect the cuffs, shoulders, armpits and hem inside the watch with thread

Children’s cotton pants cutting figure

1. Measure the baby’s size, as shown in the figure, cut the front of the pants. If it is for boys, you can mark the small in the red part

2. Cut the back piece of cotton pants. Note: the width and overall size of the back piece are slightly fatter than the front piece, and the length of the pants remains the same

3. Sew the front and back pieces, as shown in the figure. The left and right legs of the pants have been completed

4. Sew the rear crotch of the left and right legs

5. Next, let’s sew the front piece of cotton trousers. If a boy is a boy, he can leave a small hole for going to the toilet

6. Make another pair of cotton pants lining, and then put it in the outer pants

7. Put on the waistband. If you want to make it easier, you can also make the waistband of cotton trousers higher, then fold it inward, sew a gap, and put on elastic bands, which is more convenient

recommended reading

Leave a Reply

This site uses cookies to offer you a better browsing experience. By browsing this website, you agree to our use of cookies.